当前位置:返回首页 > 行业动态 > 技术文档 >

信息分类

NEWS CATEGORY

热门产品

MORE

阳极板机操作说明

2016-08-10 10:04:59

 阳极板设备操作说明

Operation instruction

 

感谢您使用本厂的剪切设备,安装使用前请务必认真阅读电控系统说明书。本系统由PLCHMI(人机界面)及外围开关按钮和接触器等器件构成,功能,性能稳定,操作简单,其连接图见附录。

Thank you for your choice of our cutting equipment. Before installing and using, be sure to read the instruction for electric control system carefully. The equipment is consisted by such components as PLC, HMI, switch button and contactor. Powerful and stable function, easy operation. See appendix for connection graph.

注意:

Attention:

1.     安装时,务必切断电源。

2.     请检查控制柜内部接线是否有运输等原因导致的接线端子松动。

3.     非人员请勿随意修改内部线路,以免发生危险。

4.     请务必以标准接地。

请依说明书要求操作。 

1. Be sure to cut off the electric power before installation.

2. Please check if the connectors in the control box are loose for the reason of transportation.

3.  Non professional staff should not change the internal electric circuit to avoid danger.

4. Be sure to connect the grounding wires correctly.

Please operate according to operating construction

安装接线

#机器电源为31零,3相火接ABC,零线接N。主电机接UVW。飞锯电机接U1V1W1。油泵电机接U1V1W1、。K1接电磁抑流阀,K1---K6分别接个电磁阀控制线,6个阀的公用零线接N

接线完成后,向上搬电箱内空气开关,整机送电,观察有无异常及异味,如有异常应立即停电检查,约一分钟后,如果   正常,开始试机。

接线时要有专人看护,注意   。设备接   地线。

Wiring method

The electric power is 3 live wires and 1 zero wire. 3 live wires connect to A, B and C separately. 1 zero wire connects to N. Main machine connects to U, V, W. Motor for flying saw connects to U1, V1, W1. Motor for oil pump connects to U1, V1, W1. K1 is for electromagnetic flow-restraining valve. K1 to K6 are seperately for electromagnetic valves. The  control lines. The shared zero wire of the six valves connects to N.

When the lines are connected correctly, turn on the switch in the control box. The whole equipment is powered. Observe whether there is abnormal state or smell. If something abnormal happens, cut off the electricity and check. About 1 minute later, state testing if all come to normal.

One person should be appointed to make sure that everything is correct when connecting wires. The equipment should adopt grounding wire.

 

调试:

所有线连接完成,先不接限位开关的插头,启动油泵(注意转向),分别点击显示屏的6组功能按键(中孔升/降、边孔升/降、切断/返回),调整电磁阀插头或者油管,使其功能相符。连接行程开关,并调整各个行程开关使其功能相符并达到相应要求。

Testing and debugging

The limit switch is off when all wires are connected correctly. Turn on oil pump (pay attention to the direction of rotataion ) and click the 6 groups of functional button on the screen(middle hole up/down, side hole up/down, cutter up/down). Adjust the plug for electromagnetic valves or oil tube to make sure that they work well with the indication of the screen.

Link and adjust the travel switches to make sure that they work well with the indication of the screen.

使用

功能按键按照屏幕说明引导使用,数据输入直接点需要修改的数据,弹出数据输入窗口,直接按数字键,输入完成按确认。

机器设置孔位,全部以材料   端为准,如下图

Using: 

Copyright © 2021-2022 http://www.hbjkywjx.com. All Rights Reserved 泊头市隆兴压瓦机械厂版权所有 冀ICP备2021011859号-1

冀公网安备 13098102001307号